ANTI GUN
Your source for military surplus.

Canadian Ross 1905 .303 Rifle US Marked with Bayonet

INFO ONLY. NOT FOR SALE. P7-6

Includes Bayonet, No Scabbard. US Marked. Light Quebec Cartouche. Flaming Bomb

The Ross rifle was a straight-pull bolt-action 0.303 inch calibre rifle produced in Canada from 1903 until the middle of the First World War, when it was withdrawn from service in Europe due to its unreliability under wartime conditions, and its widespread unpopularity among the soldiers. Although the Ross .303 was a superior marksman rifle, its mechanism proved too easily fouled in the adverse environment imposed by trench warfare in the First World War and its tight chamber dimensions were unsuitable for larger tolerance British cartridges. With the Mk III, it was also possible for a careless user to disassemble the bolt for cleaning and then reassemble it with the bolt-head rotated a half turn, causing it not to rotate and lock into the receiver. This could result in a highly dangerous and sometimes fatal bolt blow back on firing.

Caliber: .303 British (7.7x56R mm) Action: manually operated, straight pull Overall length: 1320 mm Barrel length: 711 mm Weight: 3.90 kg Magazine capacity: 5 rounds The origins of the Ross rifle lie in the late-1890s patents of the noble Canadian Sir Charles Ross, who developed his own pattern of the straight pull rifles, broadly based on Austrian Mannlicher M1890 / 1895 system. British and Canadian forces tested Ross rifles circa 1900-1901, but these rifles, while being quite fast in action, completely failed the reliability tests. The only fact that Britain refused to supply Canada with enough Lee-Enfield rifles during the second Boer war resulted in adoption of the .303 caliber Ross Mark I rifle in 1902. First rifles were delivered to Canadian military and Royal Canadian Mounted Police in 1905. These rifles were manufactured at the Ross Rifle Co, in Quebec. In 1907, Ross introduced a slightly improved Mark II rifle. Between 1907 and 1912, Ross turned out several star-marked modifications of the basic mark II pattern, which differed in barrel lengths, safety arrangements and other such minor modifications. In the summer of 1911 Canadian army introduced the Mark III Ross rifle, also known as Model 1910. This rifle was the principal arm of the Canadian corps in Europe during the First World war, and it turned out as a complete failure. Despite the modified magazine which could be loaded from stripper clips, the Ross Mark III rifle was too sensitive for dirt and fouling, it lacked proper initial extraction to handle dirty ammunition. The overly complicated bolt system of all Marks of the rifle did not helped the proper maintenance n the field, which also compromised reliability. The worst thing about the Ross system, however, was that its bolt could be eventually assembled in the wrong order, and in this case rifle could be assembled and then fired with the bolt not locked to the receiver - with disastrous results to both shooter and rifle. On the other hand, most Ross rifles were inherently accurate and served well as a sporter and even match rifles. After the end of First World War, most military Ross rifles were replaced in Canadian service with famous SMLE Mark III rifles of British origins, but made in Canada.

All Ross rifles are straight pull, manually operated, magazine fed repeaters. Separate bolt head with dual opposite locking lugs was inserted into the bolt from the front. The helical cuts and ribs forced the bolt head to rotate on opening and closing stroke of the bolt, thus unlocking and locking it to the receiver. The bolt lugs were made either in solid, Mauser-type pattern, or in interrupted-thread type pattern, depending on the rifle Mark. There were two patterns of magazines in Ross Rifles. Mark I and Mark II rifles had so called Harris controlled platform magazine. This magazine was generally similar to Mauser-type double stack magazine, but could not be loaded from stripper clips. Instead, there was an exposed finger piece, connected to the magazine follower. To load the Harris magazine, shooter had to open the bolt, depress the finger piece at the right side of the stock with its finger to compress the magazine spring and lower the follower, and then spill the five loose rounds into the magazine opening. Upon release of the finger piece the magazine follower spring is released, and bolt could be closed, thus completing the loading cycle. The Mark III rifles had a Lee-type single stack magazine, which protruded below from the stock. This magazine could be loaded from standard 5-round stripper clips, and the clip guides were machined into the front of the rear sight block. The type of rear sight was another change from the Mark II to Mark III. While Mark I and II rifles featured tangent rear sights, mounted ahead of the receiver, on the top of the barrel, the Mark III rifles featured a diopter-type rear sight, mounted on the rear bridge of the receiver. There were other variations in marks and modifications, such as in the shape of stock and handguards.


Sold Out
  • Model: INFO ONLY
  • 0 Units in Stock

CALIFORNIA RESIDENTS
WARNING: THIS PRODUCT CAN EXPOSE YOU TO CHEMICALS INCLUDING LEAD, WHICH IS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER AND BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM. FOR MORE INFORMATION GO TO WWW.P65WARNINGS.CA.GOV
This product was added to our catalog on Wednesday 17 September, 2008.

Your IP Address is: 18.97.9.168
Copyright © 2024 Buymilsurp.com Online Store. Powered by Zen Cart
Parse Time: 0.525 - Number of Queries: 369 - Query Time: 0.2184190216217